DESCRIPTION
The NEW
Krohn-Hite Model 3016 Multichannel Filter/Amplifier Signal
Conditioning System houses up
to sixteen filter/amplifier channels that provide cost effective
signal conditioning over the frequency range from 1Hz to
200kHz.
The 3016 is
completely customizable. Cutoff frequency, filter type, input and output
gains, and number of channels from 8 to 16 are all determined by the customer. The
3016 is a 3.5" chassis with BNC input and output connections.
Each filter channel is determined by
a plug-in filter/amplifier module that can be interchanged giving the
user the ability to change filter attributes when needed.
SPECIFICATIONS
FILTER
MODULE CHARACTERISTICS
Cutoff
Frequency Accuracy: 2% standard; 1% available.
Temperature Coefficient: 0.05%/°C.
Passband Response Deviation from Theoretical
(non-inverting):
Low-Pass: 1Hz to 50kHz, ±0.1dB; to 200kHz, ±0.2dB.
High-Pass (small signal, 0.4Vp-p): Input frequencies to
200kHz, ±0.1dB, -3dB point approximately 2.5MHz.
Stopband Attenuation (Signal Rejection):
Low-Pass: >100dB to 200kHz, >80dB to 1MHz.
High-Pass: >100dB.
2% standard; 1% available.
Temperature Coefficient: 0.05%/°C.
|
Harmonic
Distortion: |
Input Frequency
|
Distortion
|
10Vp-p
|
20Vp-p
|
<2kHz
|
0.003% (-90dB)
|
0.006% (-84dB)
|
2kHz to 20kHz
|
0.015% (-76dB)
|
0.03% (-70dB)
|
20kHz to 200kHz
|
0.15% (-56dB)
|
0.3% (-50dB)
|
INPUT CHARACTERISTICS
(with no input gain)
Impedance:
10k ohms or greater. Impedance will vary depending upon
cutoff frequency selected
or specified with input buffer.
Voltage Range: ±10V peak.
Maximum Safe Voltage: ±15V.
INPUT
GAIN CHARACTERISTICS
Gain: 1
to 100 in 1% increments (0dB to 40dB in 0.1dB
increments).
Input Impedance: 1M ohms or specified.
Maximum Voltage Without Damage: ±15V.
Input Type: FET.
Bias Current: Single-ended input, typically 10pA,
200pA max.; differential input, typically 2nA,
10nA max.,
(5nA max. offset current).
Gain Bandwidth (GB) Factor for Determining Useful
High-Pass Bandwidth: 2MHz.
Differential Gain:
Input Impedance: to common ground 100k ohm or
specified.
Common Mode Maximum Signal Amplitude: (differential
signal) X (input gain) + (common mode
signal)
must be
<±10V peak.
CMMR: >80dB to 60Hz with a gain of 1; >100dB
with a gain of 10 or greater.
Maximum Common Mode or Differential Mode Without
Damage: ±60V.
Gain Bandwidth: Typically 1MHz with unity input
gain; 200kHz, X100 input gain; full power
bandwidth,
typically 65kHz.
OUTPUT
CHARACTERISTICS
Impedance:
<0.1 ohms to 200kHz.
Linear Operating Range: ±10V peak (typically
±11V peak).
Low-Pass Maximum Voltage: 20Vp-p (22p-p typical),
DC to 100kHz or limited by input amplifier.
<0.1 ohms to 200kHz.
Linear Operating Range: ±10V peak (typically
±11V peak).
Low-Pass Maximum Voltage: 20Vp-p (22p-p typical),
DC to 100kHz or limited by input amplifier.
|
High-Pass
Maximum Voltage: |
Input Frequencies
|
Output Voltage
|
1Hz
|
to
|
200kHz
|
20Vp-p
|
200kHz
|
to
|
500kHz
|
10Vp-p
|
500kHz
|
to
|
1MHz
|
4Vp-p
|
Maximum
Current (2k load):
±5mA peak with 10V output.
Offset Voltage (RTI): <10mV settable to zero
with offset control.
Offset Temperature Coefficient (RTI):
<0.2mV/°C.
Noise (with input shorted to ground and detector
bandwidth of 5Hz to 300kHz): typically
25µV, 50µV rms max. referred to input.
Noise Spectral Density: <100nV/ÖHz, 100Hz to 300kHz, typically
40nV/ÖHz. For 8-pole
Butterworth
modules specification may be 3 times higher near the
cutoff region.
Signal-to-Noise Ratio (at 7V rms): >100dB.
OUTPUT GAIN CHARACTERISTICS
Gain: 1
to 100 in 1% increments (0dB to 40dB in 0.1dB
increments).
Gain Bandwidth: 100MHz for output gains of 5 or
greater. For gains less than 5, max. useful
bandwidth is
a fixed 20MHz.
Operating Range: ±10Vp-p, ±11Vp-p typical.
Maximum Current (2k load): ±5mA peak with 10V
output.
1
to 100 in 1% increments (0dB to
40dB in 0.1dB
increments).
Gain Bandwidth: 100MHz for output gains of 5 or
greater. For gains less than 5, max. useful
bandwidth is
a fixed 20MHz.
Operating Range: ±10Vp-p, ±11Vp-p typical.
Maximum Current (2k load): ±5mA peak with 10V
output.
GENERAL
Power
Requirements:
90-132/180-230
volts ac, 50-60Hz; 40 watts.
Dimensions: 10.8” (27.46cm) deep; 3.5” (8.89cm) high; 19.0”
(48.26cm) wide.
Weight: 18 lbs (8.16kg) net; 25 lbs (11.34kg) shipping.
Output Short Circuit Protection: Limited to short duration.
Operating Temperature Range: 0ºC to +40ºC.
Storage Temperature Range: -25ºC to +85ºC.
OPTIONAL
ACCESSORIES
CAB-025:
Cable, BNC, 3ft, Low Noise
Specifications apply at 25ºC ±5ºC.
Specifications subject to change without notice.
The
performance characteristics listed here are for an optimum
design. Performance
improvements in specific areas are possible with compromises in other areas.
Copyright ©
September 13, 2006
Krohn-Hite Corporation. All rights reserved.
15 Jonathan Drive, Unit 4, Brockton, MA 02301-5566 U.S.A.
Tel: (508) 580-1660; Fax: (508) 583-8989; info@krohn-hite.com
